The article which follows about How to Install a Bathtub Yourself is relatively enjoyable. Try it and make your own assumptions.
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is likewise a reasonably tough project. If the old tub is conveniently accessible, the project can move rapidly; if you have to open a wall surface to remove the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to think about utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will certainly help you install a new tub in your bathroom if you have already purchased a new bathtub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and product list should consist of the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the called for position. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bath tub up until the level reviews level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
Switch on the supply of water and also check all joints and also new pipework for leaks as well as tighten them if necessary. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub ought to wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making certain that the washing machines remain in location between the faucet and the sink. Safeguard the faucet in position with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in problems with dampness as well as feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in usage. The sealant can break relatively early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily available on the market. It is a good idea to fit the ceramic tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that report about How to Install a Bathtub from a friend on another web address. Don't hesitate to take the time to promote this post if you enjoyed reading it. I value reading our article about How to Install a Bathtub.
Schedule Service